Friday, September 23, 2011

washing machine shows F09 error on display?

Kenmore Elite and Whirlpool Duet FRONT LOADER washers shows error code F09.



WHAT DOES THIS ERROR CODE F09 MEAN?


F9 is an Overflow Condition error. If the Overflow contact on the pressure switch is closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door may remain locked, and the Drain Pump may run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.



WHAT CAN I TRY TO TAKE CARE OF THIS ERROR CODE OR GET RID OF THIS PROBLEM?


You will need to check to following:


BASIC HOUSEHOLD TOOLS LIKE SCREWDRIVER, PLIERS, PRIER, AND PUTTY KNIFE ETC ETC ARE REQUIRED. -----

ALWAYS KEEP MARKER AND HANDY-CAM READY, WHILE PERFORMING THESE JOBS.

MARKER COMES IN USE TO MARK THE POSITION OR PARTICULAR WIRE OR SCREW AND HANDY CAM COMES IN USE FOR GETTING THE EXACT PICTURE OF PART,WHEN IT WAS ASSEMBLED, SO WHILE DIS-ASSEMBLY, YOU CAN JUST VIEW THE PICTURE/PHOTO AND THAT HELPS YOU A LOT.




1. Check the drain hose and make sure it is not plugged or kinked.
2. Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU).
3. Check/Clean Drain Pump Filter of foreign objects
4. Check for Drain Pump Failure.
5. Check the Inlet Valve for proper shut off
6. Check the Pressure switch for proper operation.

1. Check the drain hose by removing it from the standpipe and pull a vacuum on it with a shop vac. It could be that you have an obstruction somewhere. You may have to check the drain pump and the drain hose just prior to the drain pump as well. This is the hose that attaches to the bottom of the tub. This area can get clogged with debris


2. Unplug the washer and remove the kick plate and top panel. Check for any loose connections at the drain pump, pressure switch (located in the right rear of the machine), and the CCU (located in the center rear of the washer behind the wash tub). You may have a loose or dirty connection somewhere. If you remove any connectors, make sure you write down where they go. It's best to only remove ONE connector at a time when checking the CCU. On the pressure switch, make sure the air hose is still attached. This is usually a clear or black rubber hose. With the air hose off, loose, or leaking, the switch will not work and the tub will continue to try to fill. The pressure switch can be checked by removing the the large connector plug from the front of the CCU at the very LEFT. Readings across pins 1 to 2, 3 to 4, 4 to 5, and 4 to 6 should ALL read 0 ohms.

3. The drain pump. Remove the clean out cover on the pump and check for debris. Make sure you drain the water from the drain lines, pump and hoses PRIOR to removing the cover. Otherwise, you will have about a gallon or so of water to clean up. The shop vac method works great for this. If the pump is running and clear of foreign matter, the pump is probably not the problem. A meter reading across the pump motor windings at the connector plug should be about 15 ohms.

4. The inlet valve. If the inlet valve would fail in this manner, the tub would be trying to fill with water all the time and not shut off (even with the washer turned OFF). You need to ask yourself if you find standing water in the tub when not in use. Replace the water inlet valve if this is the case. Readings across the HOT and/or COLD solenoids should each read about 800 ohms.

5. The suds error. This occurs when air from too much detergent gets into the drain line. If you are using HE detergent (which is great, because on the newer models NOT using HE detergent voids your warranty), but HOW MUCH are you using? Some things to consider:

a. Do you have soft water? This can actually cause the soap to suds better making the need to cut back on how much you use.

b. Look at the detergent container. Is it double or triple concentrated? Some detergents are sold as extra concentrated which means you need to cut back on the amount you use. Not doing so can cause the water to over suds.

c. What size loads are you using the detergent in? Running small loads with the same amount of detergent can also cause over sudsing.

Rule out the simple common sense things first. If everything else checks out and your problem still persists, you may have a failed CCU or pressure switch.

------------

FROM WHERE TO GET PARTS IF REQUIRED:----

Replacement parts can be purchased at any of the following web sites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

-------------------------


FOR more appliance troubleshooting help check the link below:---

For more help: ----Problem related to overfilling. Click the link below:--

Dishwasher fills with water even after turned off?

Washing machine fills with water even after turned off?

How to repair direct drive washing machines?

How to replace motor coupling on washing machines?

· Constant Beep on Kenmore Oasis washer?

· How to replace Clutch on Whirlpool Top Load washe...

· How to replace Glass Cook Top?

· how to troubleshoot an "Fdl" error code on washing...

· Using Regular Detergent on HE Washer?

· Washing machine error codes?

· Ceramic Glass Cooktops?

· How to Winterize the Washing Machine?

· How To replace the Agitator and Dogs on Kenmore S...

· Error HE3 on Kenmore Elite Quiet washer?

· ERROR F02 on Hotpoint Aquarius washer dryer

· Error F-28 on Maytag Whirlpool frontload?

· Error F-21 on Maytag Whirlpool frontload?

· How to check Drain Pump on Kenmore Elite Front Loa...

· SUD and F35 error code on Kenmore Elite washer?

· washing cycles are taking up too long to complete ...

· AF error on whirlpool cabrio?

· DE error on LG washing machine

· HC error code on Top Load Washer

· f7 error code and beeping on kenmore single elect...

Error F06 on Frigidaire Front Load Washer

How to check Drain Pump on Whirlpool Cabrio washer...

No spin problem on washing machine?

http://washingmachineforum.blogspot.com/2011/09/no-spin-problem-on-washing-machine.html

How to Level washing machine?

http://washingmachineforum.blogspot.com/2011/09/how-to-level-washing-machine.html

How to replace Water Pump on washing machine?

http://washingmachineforum.blogspot.com/2011/09/how-to-replace-water-pump-on-washing.html

How to replace water inlet valve on washing machine?

http://washingmachineforum.blogspot.com/2011/09/how-to-replace-water-inlet-valve-on.html

How to replace electronic control board on Kitchen Range?

http://washingmachineforum.blogspot.com/2011/09/how-to-replace-electronic-control-board.html

How to replace the heating element on dryer?

http://schematicsdiagram.blogspot.com/2011/09/how-to-replace-heating-element-on-dryer.html

How to troubleshoot vibration on Washing machine?

http://washingmachineforum.blogspot.com/2011/09/how-to-troubleshoot-vibration-on.html

How to install Drive Belt on washing machine?

http://washingmachineforum.blogspot.com/2011/09/how-to-install-drive-belt-on-washing.html

How to access the interior components on Whirlpool washers?

http://washingmachineforum.blogspot.com/2011/09/how-to-access-interior-components-on.html

Control Panel Lock on Washing Machines?

http://washingmachineforum.blogspot.com/2011/09/control-panel-lock-on-washing-machines.html

Washer Siphoning?

http://washingmachineforum.blogspot.com/2011/09/washer-siphoning.html

How to Check Drain Pump on Front Loader washing machine?

http://washingmachineforum.blogspot.com/2011/09/how-to-check-drain-pump-on-front-loader.html

washing machine shows FH error on display ?

http://washingmachineforum.blogspot.com/2011/09/washing-machine-shows-fh-error-on.html

washing machine shows F11 error on display ?

http://washingmachineforum.blogspot.com/2011/09/washing-machine-shows-f11-error-on.html

SUDS error on washing machine?

http://washingmachineforum.blogspot.com/2011/09/suds-error-on-washing-machine.html

Washing machine shows F05 error on display?

http://washingmachineforum.blogspot.com/2011/09/washing-machine-shows-f05-error-on.html

Washing machine shows F20 error on display?

http://washingmachineforum.blogspot.com/2011/09/washing-machine-shows-f20-error-on.html

Washing machine shows F29 error on display?

http://washingmachineforum.blogspot.com/2011/09/washing-machine-shows-f29-error-on.html

F21 Error Code on washing machine?

http://washingmachineforum.blogspot.com/2011/09/f21-error-code-on-washing-machine.html

Washing machine shows F27 error on display?

http://washingmachineforum.blogspot.com/2011/09/washing-machine-shows-f27-error-on.html

3 comments:

  1. Thanks for the post. Blogs like these are very useful for people like us who are in service field. We are into washing machine service and blogs like these are extremely helpful for us. Thanks.

    ReplyDelete
  2. Error code issues are very easy to clear once you are experienced. I run a washing machine service center and details like these are very important and useful. Thanks for the post.

    ReplyDelete
  3. Washing machine error codes which appear in automatic washing machine can be cleared easily if you are experienced. Blog post like these are very useful. We are running Washing machine service center in Chennai and posts like these does help us. Thank you.

    ReplyDelete