washingmachine: How to Replace Agitator Dogs on washing machine?

Replacing the Agitator Dogs on Kenmore and Whirlpool TOP LOADER style washing machines.

HOW TO REPAIR THE AGITATOR DOG PROBLEM?

This simple repair can save you a fortune in repair costs as the replacement parts are very inexpensive at a cost of less than $10.

WHAT IS THE PART NUMBER FOR THE PART?

The replacement kit part number is 80040.

FROM WHERE I CAN ORDER PARTS?

You can order on line at various appliance parts websites, or use this part number and go to your nearest appliance parts retailer.

PLEASE GIVE ME SOME DETAILS REGARDING AGITATOR DOGS?

What are Agitator Dogs?

These are small plastic pieces (usually 4) that are located under the agitator center cap that grip the agitator and turn it during the wash cycle. They can (and do) wear out dependent upon the use of the washer. If you are in the habit of doing large load sizes frequently, or wash large items such blankets or afghans, this can wear the teeth off and reduce the life of the agitator dogs.

WHEN SHOULD I REPLACE AGITATOR DOGS?

SYMPTOMS REQURING REPLACEMENT: The agitator fails to turn during the wash cycle, or will not turn with a heavy load. The timer will run normally through all cycles, and you will be able to hear the gearcase(transmission) engage and run. The washer will also drain normally. The only indication that something is wrong will be the agitator slipping or not turning at all. The result will be clothes that do not wash properly and will sit on the bottom of the wash tub.

CAN I REPLACE AGITATOR DOGS MYSELF.IF YES, THEN HOW?

To replace the Agitator Dogs, follow these steps:

1. Remove the agitator center cap by either pulling straight up or gently placing a flat blade screwdriver into a slot located in the cap.

2. If the agitator is equipped with an inner cap with a handle, remove this as well by pulling straight up.

3. Remove the center bolt of the agitator. You will have either a 7/16? hex bolt or a recessed square plastic nut. If you have the square recessed type, use a 3/8? to ½? ratchet adapter to remove.

4. Remove the agitator by grasping the bottom flange and carefully pulling straight up. Try to keep all the parts assembled while doing this, so do not pull too hard. This will make this repair much easier.

5. Place your hand over the top of the agitator and separate the upper portion of the agitator from the lower portion and turn the top half over in your hand. The agitator dog assembly will come out in your hand.

6. With the agitator dog assembly in your hand, lay the rest of the agitator aside. Pay careful attention to how the dogs are installed. Remove the worn dogs and reinstall new ones. It?s that simple.

7. With all the dogs replaced and the assembly still in your hand, place the upper part of the agitator over the top of it, upside down, ensuring the inner assembly tabs align correctly.

8. Now keep your hand over the agitator top to hold all the pieces together and turn the entire assembly over (upright position).

9. Carefully align and reinsert the upper portion of the agitator to the lower portion. Again, making sure the two pieces align correctly.

10. Place the entire agitator assembly back on the gearcase shaft and reinstall center nut. NOTE: DO NOT over tighten the nut, or the agitator will not spin correctly. Just make the nut snug. Reinstall center cap and inner cap (if equipped).

These instructions should give you the basics on how to perform this repair. Since there are various agitator types in use by Whirlpool and Kenmore, assembly can vary.

---------

FROM WHERE TO GET PARTS IF REQUIRED:----

Replacement parts can be purchased at any of the following web sites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

-------------------------

FOR more appliance troubleshooting help check the link below:---

For more help: ----Problem related to overfilling. Click the link below:--

washingmachine

Wednesday, September 28, 2011

How to Replace Agitator Dogs on washing machine?

Dishwasher fills with water even after turned off?

No spin problem on washing machine?

How to Level washing machine?

How to replace Water Pump on washing machine?

How to replace water inlet valve on washing machine?

How to replace electronic control board on Kitchen Range?

How to replace the heating element on dryer?

How to troubleshoot vibration on Washing machine?

How to install Drive Belt on washing machine?

How to access the interior components on Whirlpool washers?

Control Panel Lock on Washing Machines?

Washer Siphoning?

How to Check Drain Pump on Front Loader washing machine?

washing machine shows FH error on display ?

washing machine shows F11 error on display ?

SUDS error on washing machine?

Washing machine shows F05 error on display?

Washing machine shows F20 error on display?

Washing machine shows F29 error on display?

F21 Error Code on washing machine?

Washing machine shows F27 error on display?

Washing machine shows F09 error on display?

F21 Error Code on washing machine?

Washing machine shows F02 error on display?

No comments:

Post a Comment