- Unplug the washer while servicing inside the unit.
- Remove the lower kick panel under the door by removing the three 7mm screws under the bottom edge of the panel. HINT: Use a couple of blocks of wood to prop up the front feet of the washer to gain better access to the screws. Once the screws are removed the panel should drop down, and then pull off. If the panel becomes stuck, a slight tap on either side will dislodge it.
- Locate the drain pump. It will be located directly under the wash tub (it is the only pump this washer has).
- There is an access removal cover on the pump that can be removed to clean out the trap. BEFORE doing this, it is strongly recommended that you remove all residual water from the wash tub & drain line or you will have about a gallon or so inside your washer and on the floor to clean up.
- Here?s a helpful way of quickly removing the residual water. If you own a wet/dry shop vac, remove the drain hose from the standpipe at the wall and pull a vacuum with the shop vac. This will empty the wash tub, pump and drain lines. If you don?t own a shop vac, grab a bunch of old towels and open the access on the pump slowly so that it comes out at a trickle. Allow the towels to soak up the majority of the water. Close the access and stop the water if you need to get additional towels.
- Open the pump access and remove once you have all the water drained. Check the drain pump for foreign objects and debris. Check the pump impeller and make sure there?s nothing caught in it.Items as small as toothpicks or cotton swabs have been known to stop this pump from working.
- Clean out the pump thoroughly and reinstall the access cover. Make sure the cover is snug, but do not over tighten.
- Place the drain hose back in the standpipe (IMPORTANT ? DO NOT FORGET!).
- With the bottom panel still off, plug the washer back in and select the following on the operator console ? DRAIN SPIN, NO SPIN, and then press any button under OPTIONS 4 times (it must be the same button). ?C00? will show on the console display as the washer begins diagnostics mode.
- Check the drain pump for leaks as the washer fills. The pump is gravity filled and will hold water even it is not pumping. Allow washer to run through diagnostics until it begins the wash tub tumble cycle.
- At this point, you can stop the diagnostics procedure by pressing PAUSE/CANCEL 2 times. The drain pump energizes and the washer will begin to drain.
- If the drain pump works normal and there are no leaks detected, reinstall the bottom panel and tighten screws.
NOTE: --- It is normal to have residual water left inside the wash tub under the wash basket. This is why it is important to leave the door ajar when not in use so this water does not become sour.
searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com
FOR more appliance troubleshooting help check the link below:---
For more help:----Problem related to overfilling.Click the link below:--
Dishwasher fills with water even after turned off?
Washing machine fills with water even after turned off?
How to repair direct drive washing machines?
How to replace motor coupling on washing machines?
· Constant Beep on Kenmore Oasis washer?
· How to replace Clutch on Whirlpool Top Load washe...
· How to replace Glass Cook Top?
· how to troubleshoot an "Fdl" error code on washing...
· Using Regular Detergent on HE Washer?
· Washing machine error codes?
· How to Winterize the Washing Machine?
· How To replace the Agitator and Dogs on Kenmore S...
· Error HE3 on Kenmore Elite Quiet washer?
· ERROR F02 on Hotpoint Aquarius washer dryer
· Error F-28 on Maytag Whirlpool frontload?
· Error F-21 on Maytag Whirlpool frontload?
· How to check Drain Pump on Kenmore Elite Front Loa...
· SUD and F35 error code on Kenmore Elite washer?
· washing cycles are taking up too long to complete ...
· AF error on whirlpool cabrio?
· DE error on LG washing machine
· HC error code on Top Load Washer
· f7 error code and beeping on kenmore single elect...
Error F06 on Frigidaire Front Load Washer
How to check Drain Pump on Whirlpool Cabrio washer...
No spin problem on washing machine?
http://washingmachineforum.blogspot.com/2011/09/no-spin-problem-on-washing-machine.html
How to Level washing machine?
http://washingmachineforum.blogspot.com/2011/09/how-to-level-washing-machine.html
How to replace Water Pump on washing machine?
http://washingmachineforum.blogspot.com/2011/09/how-to-replace-water-pump-on-washing.html
How to replace water inlet valve on washing machine?
http://washingmachineforum.blogspot.com/2011/09/how-to-replace-water-inlet-valve-on.html
How to replace electronic control board on Kitchen Range ?
http://washingmachineforum.blogspot.com/2011/09/how-to-replace-electronic-control-board.html
How to replace the heating element on dryer?
http://schematicsdiagram.blogspot.com/2011/09/how-to-replace-heating-element-on-dryer.html
How to troubleshoot vibration on Washing machine?
http://washingmachineforum.blogspot.com/2011/09/how-to-troubleshoot-vibration-on.html
How to install Drive Belt on washing machine?
http://washingmachineforum.blogspot.com/2011/09/how-to-install-drive-belt-on-washing.html
How to access the interior components on Whirlpool washers?
http://washingmachineforum.blogspot.com/2011/09/how-to-access-interior-components-on.html
Control Panel Lock on Washing Machines?
http://washingmachineforum.blogspot.com/2011/09/control-panel-lock-on-washing-machines.html
No comments:
Post a Comment